鍋爐倉泵是鍋爐輸灰系統的重要組成部分，其直接影響輸灰系統的除灰效果。轉化果平臺推薦的《提高鍋爐倉泵儀表穩定運行性研究》，針對倉泵儀表故障頻繁問題，從設備、環境等方面對故障現象進行原因分析，制定相應方案對策并逐一進行實施，有效減少了倉泵的檢修次數，降低了勞動程度，取得較好經濟效益。

　　The boiler compartment pump is an important component of the boiler ash conveying system, which directly affects the ash removal efficiency of the ash conveying system. The "Research on Improving the Stable Operation of Boiler Warehouse Pump Instruments" recommended by the Conversion Fruit Platform analyzes the causes of frequent failures in warehouse pump instruments from equipment, environment, and other aspects. Corresponding solutions and countermeasures are formulated and implemented one by one, effectively reducing the number of maintenance times for warehouse pumps, lowering labor levels, and achieving good economic benefits.

　　一、研究背景

　　1、 Research background

　　鍋爐輸灰系統專門用于處理鍋爐排向大氣煙氣中的粉塵，經過除塵器、倉泵、灰庫儲運外運等環節完成對粉塵的處理。倉泵運行狀態直接影響輸灰系統的除灰效果，故障率高會(huì )對環保產生不利，增加運行成本，并影響鍋爐的安全運行，因此倉泵的穩定運行尤為重要。 項目研究目標：實現降本增效、節能降耗要求，解決倉泵頻繁加壓超時的現象，降低倉泵儀表故障次數，提高倉泵運行穩定性，達到安全環保高效運行。

　　The boiler ash conveying system is specifically designed to handle the dust emitted from the boiler into the atmosphere. The dust is processed through processes such as dust collectors, bin pumps, and ash storage and transportation. The operating status of the silo pump directly affects the ash removal efficiency of the ash conveying system. A high failure rate can be detrimental to environmental protection, increase operating costs, and affect the safe operation of the boiler. Therefore, the stable operation of the silo pump is particularly important. Project research objective: To achieve the requirements of cost reduction, efficiency improvement, energy conservation and consumption reduction, solve the phenomenon of frequent pressurization and timeout of warehouse pumps, reduce the number of instrument failures of warehouse pumps, improve the stability of warehouse pump operation, and achieve safe, environmentally friendly and efficient operation.

　　某單位月度鍋爐倉泵檢修統計表

　　Monthly Boiler Storage Pump Maintenance Statistics Table for a Certain Unit

　　二、研究?jì)热?/p>

　　2、 Research content

　　1.要因分析

　　1. To analyze the reasons

　?。?）閥門材質不符合工況要求

　　(1) The valve material does not meet the working condition requirements

　　對1#鍋爐1-3月倉泵儀表故障進行調查統計。從故障統計表可以看出，倉泵故障現象中，原因最多的是閥門故障，其占比最多。

　　Conduct investigation and statistics on the instrument failures of the storage pump in boiler 1 from January to March. From the fault statistics table, it can be seen that the most common cause of warehouse pump faults is valve failure, which accounts for the largest proportion.

　　改造之前選用的出料閥閥芯是鑄鋼材質，易沖蝕，密封性差，壽命短。閥門預期壽命為180天，而實際情況由于閥門動作頻繁、物料沖蝕等原因，導致閥門實際使用壽命短，實際與預期工作壽命相差較大，要頻繁檢修更換閥門。

　　The discharge valve core selected before the renovation is made of cast steel material, which is prone to erosion, has poor sealing performance, and has a short service life. The expected service life of the valve is 180 days, but in reality, due to frequent valve movements, material erosion, and other reasons, the actual service life of the valve is short, and there is a significant difference between the actual and expected working life, requiring frequent maintenance and replacement of the valve.

　?。?）儀表接地、隔離措施不規范

　　(2) Improper grounding and isolation measures for instruments

　　物料在倉泵內流動過程中會(huì )產生靜電，靜電通過倉泵遠傳壓力變送器信號回路傳輸至PLC控制柜內造成控制柜內電壓波動大。由于儀表接地、隔離措施不規范，易損壞PLC控制模塊和壓力變送器等，致使倉泵頻繁加壓超時，產生報警，無法正常投運。

　　During the flow of materials in the warehouse pump, static electricity is generated, which is transmitted to the PLC control cabinet through the remote pressure transmitter signal circuit of the warehouse pump, causing large voltage fluctuations in the control cabinet. Due to non-standard grounding and isolation measures for instruments, it is easy to damage PLC control modules and pressure transmitters, resulting in frequent pressurization timeouts of the bin pump, generating alarms and preventing normal operation.

　?。?）壓力變送器安裝位置不當壓力變送器安裝于控制柜內，與倉泵相連接的導壓管過長容易積灰，致使倉泵壓力測量不準，導致倉泵頻繁加壓超時故障報警。

　　(3) Improper installation position of pressure transmitter. The pressure transmitter is installed in the control cabinet, and the pressure pipe connected to the bin pump is too long, which can easily accumulate dust, resulting in inaccurate pressure measurement of the bin pump and frequent pressure exceeding fault alarms.

　　從人、機、料、法、環五個方面集思廣益對故障現象（頻繁加壓超時）可能發生的原因進行徹底的分析。最終得到了：閥門材質不符合工況要求、壓力表安裝位置不合理、儀表接地隔離措施不規范的三條主要原因。

　　Thoroughly analyze the possible causes of the fault phenomenon (frequent pressure exceeding the time limit) from five aspects: human, machine, material, method, and environment. Finally, three main reasons were identified: valve material not meeting operating requirements, unreasonable installation position of pressure gauges, and non-standard grounding and isolation measures for instruments.

　　2.制定實施對策（1）閥門重新選型通過查閱資料，選擇合適的耐沖蝕的陶瓷材質閥門；安裝、配置氣源管、調試閥門，確保閥門動作正常。

　　2. Develop implementation strategies: (1) Re select valves by consulting relevant materials and selecting suitable ceramic valves that are resistant to erosion; Install and configure the gas source pipe, debug the valve, and ensure that the valve operates normally.

　　實施效果：

　　Implementation effect:

　?、俑鼡Q完耐沖蝕陶瓷閥后查看閥門趨勢，開關正常且規律；②有效解決了流灰對閥內件的沖蝕，閥門使用周期從20多天增長為200多天，使用壽命大幅提升；確保了閥門良好的密封性，解決倉泵因出料閥密封不嚴而泄露的問題，保證整個系統連續穩定運行。

　?、?After replacing the erosion resistant ceramic valve, check the valve trend and ensure that the opening and closing are normal and regular; ② Effectively solved the erosion of valve internals caused by flowing ash, and the service life of the valve increased from over 20 days to over 200 days, significantly improving its service life; Ensure good sealing of the valve, solve the problem of leakage of the bin pump due to poor sealing of the discharge valve, and ensure the continuous and stable operation of the entire system.

　?。?）儀表回路增加安全柵、現場增加接地

　　(2) Add safety barriers to the instrument circuit and increase grounding on site

　　確認控制柜安全柵供電方式及型號；對選型好的安全柵進行組態、安裝、接線、調試；對控制柜及現場儀表增加接地。實施效果：①安全柵可以起到很好的隔離高電壓、大電流的作用。增加安全柵，以次消除靜電，保護電路和設備；②增加儀表接地，將靜電與儀表設備有效隔離，從根本上消除現場靜電對控制柜PLC模塊的不良影響，避免壓力變送器的損壞，消除故障報警。（3）壓力變送器重新安裝

　　Confirm the power supply mode and model of the control cabinet safety barrier; Configure, install, wire, and debug the selected safety barriers; Add grounding to the control cabinet and on-site instruments. Implementation effect: ① Safety barriers can effectively isolate high voltage and high current. Add safety barriers to eliminate static electricity and protect circuits and equipment; ② Add instrument grounding, effectively isolate static electricity from instrument equipment, fundamentally eliminate the adverse effects of on-site static electricity on the control cabinet PLC module, avoid damage to pressure transmitters, and eliminate fault alarms. (3) Reinstall the pressure transmitter

　　考慮到導壓管過長，容易堵塞造成壓力表測量不準，將變送器由原來控制柜內移至倉泵取壓口上方；安裝方式由水平安裝改為垂直安裝。

　　Considering that the pressure pipe is too long and prone to blockage, causing inaccurate measurement of the pressure gauge, the transmitter was moved from the original control cabinet to above the pressure tap of the bin pump; The installation method has been changed from horizontal installation to vertical installation.

　　實施效果：同比活動前，壓力變送器故障次數下降明顯，在10月、11月次數為零，從根本上解決了變送器積灰、測量不準及導壓管過長堵塞的問題。

　　Implementation effect: Before the year-on-year activity, the number of pressure transmitter failures decreased significantly, reaching zero in October and November, fundamentally solving the problems of transmitter dust accumulation, inaccurate measurement, and long and blocked pressure pipes.

　　三、應用效果

　　3、 Application effect

　　1.改造效果

　　1. Transformation effect

　　根據對改造前后故障現象加壓超時頻次及倉泵故障次數對比統計，加壓超時頻次呈逐漸遞減趨勢，在11月份開始趨于穩定狀態。故障現象逐漸減少，倉泵的故障次數也在遞減，降低了倉泵儀表故障次數。2.經濟效益改造前出料閥每月平均消耗2.3臺，每臺閥門單價8600元，共累積維修費用約24萬元；改造后統計出料閥每月平均消耗0.3臺，每臺閥門單價12000元，累計維修費用約4萬元，每年節約費用約19萬元。3.社會(huì )效益通過改造，降低了倉泵故障次數，有效減少人員檢修頻次，降低了傷害的風險，減少了非計劃停車，倉泵處于良好的工作狀態，避免粉塵泄露問題，有效提高周?chē)h(huán)境質量。

　　According to the comparison and statistics of the frequency of pressure exceeding and the number of warehouse pump failures before and after the renovation, the frequency of pressure exceeding gradually decreased and began to stabilize in November. The occurrence of faults is gradually decreasing, and the number of faults in the warehouse pump is also decreasing, reducing the number of instrument faults in the warehouse pump. Before the economic benefit transformation, the average monthly consumption of discharge valves was 2.3 units, with a unit price of 8600 yuan per valve, and the cumulative maintenance cost was about 240000 yuan; After the renovation, the average monthly consumption of discharge valves is 0.3 units, with a unit price of 12000 yuan per valve. The cumulative maintenance cost is about 40000 yuan, and the annual cost savings are about 190000 yuan. 3. Social benefits: Through renovation, the number of pump failures in the warehouse has been reduced, the frequency of personnel maintenance has been effectively reduced, the risk of injury has been lowered, unplanned parking has been reduced, the warehouse pump is in good working condition, dust leakage problems have been avoided, and the surrounding environmental quality has been effectively improved.